Electronic Vehicle Information Center (EVIC) Displays

When the appropriate conditions exist, the EVIC displays the following messages:
• Turn Signal On (with a continuous warning chime after one mile traveled)
• Left Front Turn Signal Lamp Out (with a single chime)
• Left Rear Turn Signal Lamp Out (with a single chime)
• Right Front Turn Signal Lamp Out (with a single chime)
• Right Rear Turn Signal Lamp Out (with a single chime)
• RKE (Remote Keyless Entry) Battery Low (with a single chime)
• Personal Settings Not Avail – Vehicle Not In PARK
• Personal Settings Not Avail – Vehicle in Motion
• Door Ajar (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in motion).
• Doors Ajar (with vehicle graphic showing which doors are open. A single chime sounds if the vehicle is in motion).
• Trunk Open (with vehicle graphic showing and open trunk and A single chime )
• Lights On
• Key In Ignition
• Remote start aborted — Door ajar
• Remote start aborted — Hood ajar
• Remote start aborted — Trunk ajar
• Remote start aborted — Fuel low
• Remote start disabled — System fault
• Oil Change Required (with a single chime)
• Low Tire (with a graphic of the car showing which tire(s) is/are low - with a single chime). Refer to Tire Pressure Monitoring System in Starting and Operating.
• Check TPM System (with a single chime) Refer to Tire Pressure Monitoring System in Starting and Operating.
• Gear Not Available — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Shift Not Allowed — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Shift To Neutral - Then D Or R — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Autostick Not Available — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Automatic Mode Not Available—Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Reduce Gear Changes — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Trans. Getting Hot Press Brake — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Trans. Hot Stop Safely Shift To P — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Service Transmission — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Service Shifter — Refer to Automatic Transmission/ Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Engage Park Brake — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Trans. Hot Wait To Cool — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.
• Trans. Cool Ready To Drive — Refer to Automatic Transmission/Six-Speed Automatic Transmission (C635) – If Equipped in Starting and Operating for further information.

    See also:

    Linking And Unlinking The Remote Keyless Entry Transmitter To Memory
    Your RKE transmitters can be programmed to recall one of two pre-programmed memory profiles by pressing the UNLOCK button on the RKE transmitter. To program your RKE transmitters, perform the fol ...

    Sunshade Operation
    The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. ...

    SET/RND Button — To Set the Pushbutton Memory
    When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1–6) you wish ...